Old wiring trips and heats up behind the wall. At Swift MEP, get electrical wiring & rewiring services in Dubai with right cable and protected circuits so your power stays safe & stable.
Electrical Projects
Electrical Repairs
Safety Guaranteed
Emergency Electricians
Whether it is one new circuit or complete villa, our wiring services in Dubai cover:
Complete electrical rewiring, replacing old or damaged cabling from the distribution board to every socket, switch and light point.
ideal when only the kitchen, bathroom or older wing of the property needs attention.
Fresh wiring for ACs, water heaters, ovens, EV chargers and heavy equipment that can’t share a socket.
Board upgrades, new MCBs and RCDs and correct labelling so every circuit is identified.
Office and retail fit-out wiring, gypsum partitions, floor boxes, trunking and false ceiling routing.
IP-rated cabling and connections for pumps, gates, garden lighting and pergolas.
People across Dubai choose us for wiring and rewiring work for these reasons:
We choose the right cable size for the actual load and run length.
Every circuit gets the right MCB or RCD rating for what it feeds.
Continuity, polarity & RCD trip times are tested for electrical wiring repair service.
We plan routes to keep chasing and wall cutting as low as possible.
Your distribution board is labelled so you know what each breaker controls.
We make sure your property looks tidy and in perfect condition before leaving.
Here is what our standard electrical wiring and rewiring service in Dubai looks like:
We check the existing board, cable condition, circuit layout before anything.
We split the load so heavy appliances get their own supply instead of overloading.
Power is switched off at the board and old cabling is safely disconnected.
Cable is run through conduit, trunking or false ceiling with proper support.
Points, switches and the distribution board are wired with earthing and bonding done.
We test the installation, label the board and show you the final results.
Searching for house rewiring near me because breakers keep tripping? Swift MEP covers Downtown Dubai, Business Bay, Dubai Marina, JLT, JBR, Deira, Bur Dubai, Al Quoz, Al Barsha, JVC, JVT, Palm Jumeirah, Jumeirah Park, Dubai Hills, Mirdif, Silicon Oasis, Motor City and Arabian Ranches.
We handle full villa electrical rewiring, apartment rewiring, new wiring circuits, distribution board wiring and fit-out electrical works. Whether you need a complete electrical wiring repair service or a single new circuit, our team gets it done right with 5 year+ expertise, certified electricians, 5/5 rating, same-day service and 30-minute arrival for emergency wiring jobs in Dubai.
Old cabling causing trouble or your new space needs wiring? Contact Swift MEP now.
You can also book these relevant electrical services:
We replace damaged circuit breakers, MCBs & fuse boxes for electrical safety.
Emergency electricians in Dubai for power failures & urgent electrical problems.
From LED/ceiling lights to outdoor lighting, we install every fitting neatly.
We repair faulty switches and install new power outlets for safe use.
Your queries here.
The cost ranges from AED 1000 to AED 30,000+ on an average, based on the size of the property, the number of points, cable runs and whether walls need chasing. A single new wiring circuit costs far less than a full villa electrical rewiring.
Frequent tripping, warm or discoloured sockets, a burning smell, lights dimming when appliances start and old rubber are the usual signs. We test insulation resistance to confirm whether full electrical wiring & rewiring services in Dubai are needed or a wiring repair will fulfill the purpose.
Not usually for partial work. For a full villa electrical rewiring, we work zone by zone so parts of the property stay live. If heavy dust is involved then clients need to move out for the heaviest days only.
A single circuit is often finished the same day. An apartment typically takes a few days. A full villa rewire depends on size, number of points and number of walls. We give you a schedule after the site survey.
Yes. Heavy loads need their own circuit, cable and a suitable breaker at the board. We check spare capacity at your distribution board first and tell you if the board needs upgrading before the new wiring is added or not.
